The device detects and marks the hot spot of highest temperature.ĭevice supports pallet switch and distance measurement.īuilt-in memory module supports video recording/snapshot capturing.ĭevice supports 1×, 2×, 4×, and 8× digital zoom.ĭevice can capture snapshots, record videos, and set parameters via APP after being connected to your phone. The device realizes distance measurement function after marking the top and bottom of target, and input the target height. The monocular is mainly applied to scenarios such as patrolling, law enforcement, searching and rescuing, drug enforcement, anti-smuggling, criminal seizing, hiking, travel, and hunting, etc. The high-sensitivity built-in thermal detector provides you with clear view even in total darkness. It supports functions of observation, highest temperature target tracking, distance measurement, Wi-Fi hotspot, and so on. If you have any confusions or suggestions, please contact us.The Taipan handheld observational thermal monocular is equipped with a 384×288 infrared detector and a 1280×960 LCOS display.
It is the same as current function except for the reticle type (we added several common reticles) Sighting because they are unnecessary in this mode with image calibration and riflescope scale. (It can switch modesĪutomatically by sensing eyepiece/riflescope)Īs listed above, whole image can be adjusted to align with user’s riflescope. Note: This firmware supports two modes - Clip-on mode and Scope mode. The inner whole image can be adjusted in 4 directions so as to align with user’s riflescope. We added some new reticles in thisĪfter upgrading the main firmware, FPGA firmware and Reticle firmware, press “△” and “▽“ at the same time to enter The updated time of FPGA firmware is about 15mins, so please keep patient.
#Agm taipan tm19 upgrade
Upgrade Main firmware, FPGA firmware and Reticle firmware one by one using the same method. Upgrade process would start automatically.Ģ. Unzip the package and put digicap.dav inside to root folder of device through USB cable, then reboot the device. (Restore option is in the menu)īefore downloading the firmware files, you should be registering properly on our official website to get the best support.Īdditional information for upgrading methods for Rattlers TS and TC (thermal sight and thermal clip on)ġ. Turn off the device and disconnect it from your PC.Ĩ.
#Agm taipan tm19 update
When multiple update files are present for upgrade, each update will vary in length from 4-12 minutes.ħ. If update file was added to that folder, delete it and re-copy it from downloaded folders to the root directory of the device (USB drive). If no "Updating" screen comes up in the scope make sure that the file digicap.dav is in the root directory of the device( USB) not in the DCIM, the DCIM is where images and videos are stored that are taken with the unit.
The update process will be completed when the inscription "Upgrading. During the update, the screen will display the inscription "Upgrading. After about 1 minute, the firmware update process will start automatically. dav file and paste it to the root directory of the device (USB drive).Ħ. Open the detected disk (USB drive) in file manager program. Disable the Wi-Fi Hotspot function in the device menu if WiFi is enabled.Ĥ. The high sensitivity built in thermal detector provides you. It supports functions of observation, highest temperature target tracking, distance measurements, WiFi hotspot, and more. The handheld is equipped with a 384 x 288 infrared detector and a 1280 x 960 LCOS display.
#Agm taipan tm19 Pc
Connect the thermal device to your PC with USB cable.ģ. The AGM Taipan TM19 will give you a clear view even in total darkness. Otherwise, the device will shut off and may cause unnecessary upgrade failure, firmware damage, etc.ġ. If you removed the batteries, please make sure the device is connected to the computer during the update process. If your device does not have a built-in rechargeable battery and is powered by replaceable Lithium batteries, remove the batteries from the battery compartment before connecting the device to your PC, or it may cause computer damage. Complete updating procedures for each folder. They will need to be updated in this order FPGA, Main, then Reticle. If there are multiple folders with digicap.dav files you must use one at a time. Compare the number with the latest version of the firmware on the AGM website.ĭownload the firmware update package to your PC and unzip it.ĭo not open the DAV or BIN file on your computer as it may corrupt the file. Please read the instructions below before updating the firmware.Ĭheck current firmware version of your device, for this go to your device’s main menu to option “Info” or “Version” and check what number you have.
0 kommentar(er)
